Price: $98.52
(as of Aug 03, 2025 03:27:00 UTC – Details)
Product Description
Prevent damage and eliminate costly repairs by protecting your keel against abrasive sand, rocks, concrete ramps, and oyster beds.
Hydrodynamic drag reduction design features self-sealing contoured edges and uses the highest quality materials and 3M premium adhesives.
Protect your vessel against abrasive wear during normal use for as long as you own your boat!
Frequently Asked Questions
Can I Install a KeelGuard on a Kayak or Canoe? Because most kayaks and canoes are made out of low-surface energy plastics, our Keelguard is not compatible with either as the 3M adhesive doesn’t bond to LSE plastic.
Can I Install a KeelGuard on a Jet Ski, Ski-Doo, Wave Runner, or Other Personal Watercraft (PWC)? Our KeelGuard is not compatible with modern hull designs and must be installed 4-6 inches above the resting water line.
Can I Install a KeelGuard on a Catamaran? The KeelGuard is not compatible with most Catamarans due to having very sharp keels with a steep 90° upturn. Please call Megaware directly if you have questions about your Catamaran.
Can I Install a KeelGuard on an Aluminum Boat? The KeelGuard can be installed on some aluminum boats. If your boat has a raised or reinforced center keel, it cannot be raised higher than 1/4 inch. The center keel cannot have any reinforced welding around the edge, rivets, or sharp angles. If you have compatibility questions, please contact Megaware directly. Not compatible with: Lund, Alumacraft, Smoker Craft, Crestliner, or Tracker
Can I Install the KeelGuard on a Pontoon Boat? The KeelGuard cannot be installed on the bottom of pontoon tubes. For the side of pontoon tubes, we recommend the Pontoon Guard.
Can I Apply the KeelGuard Over Strakes or Chines? Yes, the KeelGuard can be applied over slightly raised strakes and chines. NOTE: must apply sealant over strakes/chines areas to seal off gaps and prevent water from getting under the adhesive
Can I Apply the KeelGuard Over a Vinyl Wrap? The KeelGuard is not recommended to install over boat wrap. Must be installed on the actual surface of the boat. We do not recommend installing the KeelGuard over a vinyl wrap because it will pull the wrap off the boat.
Can I Apply the Megaware KeelGuard Over Boat Bottom Paint or Anti-Fouling Paint? Anti-fouling or boat bottom paint must be removed prior to installing the KeelGuard. You can apply boat bottom or anti-fouling paint OVER the KeelGuard once you have installed it to the actual surface of the boat.
Why Do I Have to Install the KeelGuard 4-6 inches ABOVE the Resting Water Line if I’m Only Using it for Beaching? When you get your boat up to speed, the water pressure can cause the KeelGuard to peel off the hull. To avoid this, apply it 4-6 inches above the water line.
Can I Install a KeelGuard Below the Water Line? Do not install the KeelGuard below the water line. Water pressure against the leading edge of the KeelGuard when bringing your boat is up to plane can cause it to peel off.
Can I Install a KeelGuard if My Boat Sits on Trailer Rollers? The KeelGuard cannot touch, sit on, or rest against anything such as bunks, rollers, v-blocks, or bow stops while sitting on the trailer. These “pressure points” destroy the 3M adhesive and the KeelGuard will fail. Please check your boat trailer for compatibility.
What if My Boat Sits on a Floating Dock? Do not let the KeelGuard touch or rest against anything, as it will destroy the 3M adhesive and cause it to fail or when launching the KeelGuard could snag on the dock and tear.
Can I Install a KeelGuard Shorter Than the Recommended Length or Cut it Shorter? The KeelGuard is designed to extend beyond the lowest point of the boat to prevent snagging and tearing when beaching or loading your boat. You can exceed the recommended length, but not shorten it.
Will the KeelGuard create drag and reduce the speed of my boat? The Megaware KeelGuard is designed for the marine environment with patented drag reduction technology and won’t slow your boat down.
Is it Possible to Remove the Megaware KeelGuard? In the unlikely event you need to remove a Megaware KeelGuard, it can be done. The foam core of the 3M adhesive is designed to split in the middle when you pull the KeelGuard. To remove the adhesive from the boat use a putty knife and pinstripe removal disc.
The Keel of My Boat has Damage, Can I Install a KeelGuard Over the Damaged Area? A good surface is crucial for proper KeelGuard installation. Damage to the boat’s keel, unprofessional repairs, or poorly bonded paint or gel coat can cause the KeelGuard to fail. It is recommended to repair any damage before installing a KeelGuard.
Can I Install the KeelGuard on a Hot or Cold Day? 3M advises against applying the adhesive when the hull temperature is below 65°F or above 100°F. Ideally, bring the boat into a garage to warm up or cool down to the acceptable temperature range. Both the KeelGuard and boat hull should be at the same temperature during application.
Boat Keel Protector – Protect your boat keel from sand, rocks, oyster beds, concrete ramps, and everyday wear and tear on the water with The Original Do-It-Yourself Keel Guard from Megaware. Note: compatible with fiberglass and some aluminum boats
Easy to Install – The boat protector features an exclusive self-sealing contoured edge that creates a clean, tight seal; no messy sealants needed. Easy install in 4 simple steps; etch, clean, prime, apply!
Superior Engineering – This patented hydrodynamic drag reduction design is produced using the highest quality materials and 3M premium adhesives. Pliable and tough, the 5-inch wide boat keel protection easily conforms to your boat’s keel; it’s shock absorbing, exclusive contoured edge design, and drag reduction channels won’t slow your boat down
9 Standard Length Kits – Our boat keel guard comes in 9 different sizes that range from 4 to 12 feet long to ensure you have the correct size; shields come in 12 colors that will not fade or dull while enhancing the look of your boat. Note: if the size of your boat falls between 2 sizes, order a size up for additional keel protection
Lifetime Warranty – The Megaware KeelGuard is so tough and reliable that we include a lifetime warranty during normal use of your boat, for as long as you own your boat.
Customers say
Customers find the keel guard easy to install, taking about 60-90 minutes, and appreciate its heavy-duty construction and effectiveness in protecting against sand, rocks, and oyster beds. Moreover, the product receives positive feedback for its functionality, appearance, and value for money, with customers noting its color match and durability. However, customers disagree on the adhesion quality, with some reporting it doesn’t stick well. Additionally, several customers mention that the product starts coming off after one season of use.
